新闻资讯【INFORMATION】
- 安装轻质隔墙板构件要求
- 本站编辑:杭州久泰建材有限公司发布日期：2019-09-20 13:19 浏览次数：
安装构件要求
1、顶端与梁底用U型铁件固定，将U型铁件用射钉固定在梁底部，上端用木楔加固，用L型铁件固定。
2、吊挂设计：吊挂间距不应小于300m，单点承重不应大于80公斤，需先开口埋件。
3、电气设计：电气线路可作暗线设计，利用隔墙板孔穿软管敷设线路；也可作明线设计，敷于墙面，开口插座与其相应配置。
4、防潮防水：饰面设计应考虑防潮防水，沿墙边设计水池、水箱、面盆等附件时，墙面应涂刷防水涂料或贴瓷砖等防水饰面设计。
5、墙面装修：可刮大白、喷瓷、贴瓷砖等装饰材料进行装修。进行下道工序装修时，先清理隔墙板墙面，洒水润湿，按常规的施工工艺进行装修 。
Installation Component Requirements
1, the top and the bottom of the beam are fixed with U-type iron pieces, the U-type iron pieces are fixed with nails at the bottom of the beam, the upper end is reinforced with wood wedges, and the L-type iron pieces are fixed.
2, hanging design: hanging spacing should not be less than 300M, single point load should not be greater than 80 kg, need to open and bury the piece first.
3, electrical design: electrical lines can be used for dark line design, using the wall panel Kongchuan hose laying line; It can also be used as a bright line design, applied to the wall, opening socket and its corresponding configuration.
4, moisture-proof waterproof: the design of the finish should be considered moisture-proof waterproof, along the wall edge design pool, water tank, basin and other accessories, the wall should be painted waterproof paint or tiles and other waterproof finish design.
5, wall decoration: can scratch white, spray porcelain, paste tile and other decorative materials for decoration. When the next procedure is decorated, clean the wall of the partition first, sprinkle water and moisten it, and decorate it according to the usual construction techniques.
Installation Component Requirements
1, the top and the bottom of the beam are fixed with U-type iron pieces, the U-type iron pieces are fixed with nails at the bottom of the beam, the upper end is reinforced with wood wedges, and the L-type iron pieces are fixed.
2, hanging design: hanging spacing should not be less than 300M, single point load should not be greater than 80 kg, need to open and bury the piece first.
3, electrical design: electrical lines can be used for dark line design, using the wall panel Kongchuan hose laying line; It can also be used as a bright line design, applied to the wall, opening socket and its corresponding configuration.
4, moisture-proof waterproof: the design of the finish should be considered moisture-proof waterproof, along the wall edge design pool, water tank, basin and other accessories, the wall should be painted waterproof paint or tiles and other waterproof finish design.
5, wall decoration: can scratch white, spray porcelain, paste tile and other decorative materials for decoration. When the next procedure is decorated, clean the wall of the partition first, sprinkle water and moisten it, and decorate it according to the usual construction techniques.
- 上一篇：轻质隔墙板怎么样开线槽呢
- 下一篇：轻质墙板的防水效果怎样判断
Copyright